Français
My account Register
Français
EVO-START Wirecolor

Your Cart

Your shopping cart is empty.

Your shopping cart is empty.

Continue Shopping

ESTIMATED TOTAL:

Checkout

QUICK VEHICLE FINDER

VEHICLE FINDER

User

Anthony Wilkinson

Joined on the:

Nov. 10, 2018

Score

7090

Comment(s)

32

Voted question(s)

0

Voted answer(s)

0

Votes up

0

Votes down

0

Votes up received

0

Votes down received

0

Recent Activity

Question(s) asked

2

Answered question(s)

90

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question
RECENT ACTIVITY QUESTION(S) ASKED ANSWERED QUESTION(S) COMMENTED QUESTION(S)

07/02/2019

 Mazda Matthew Walters (130Pts.)

0

Cannot program keys to 2014 Mazda 6 Automatic: evoall with maz t-harness and linkr module

I have a 2014 mazda 6 automatic and I'm trying to program the evoall with T harness and linkr. I am using guide 62781. It recogniZed my keys with the yellow light, but after the second key instead of getting yellow and red alternating, it cycles through blue, yellow, and red. I still hooked the evoall up to my computer and the dcrypt was successful. When I go back to my car, I try to go through steps 1-12 again, but I don't get a yellow light this time when I push the start button twice with my keys. I've flashed the unit to the latest firmware. I've also reset the unit multiple times. I have the hood pin wire grounded out, however I do not have pin 11 in the under hood fuse box grounded yet. Could that be the problem with programming, and what do the three alternating lights mean?
Login to reply View 1 answer(s)

06/02/2019

 Kia Pheaktra Mom (860Pts.)

0

Where does wire D1 go at the "Cut"?

On a Kia Sorento 2019, it says cut wire at D1. Where does the wire (D1) go after cutting it? Theres also dotted lines in between.. Im guessing it connects to the other wires (D3/A10) towards the connector? This is for a Kia Sorento 2019 push to start and evo one regular installation.
Login to reply View 1 answer(s)

06/02/2019

 Jeep Jeep Guy (160Pts.)

0

Viper smartstart not communicating with EVO ALL

I've installed a VSM350 in my 2008 Grand Cherokee, following the instructions (splice grey wire with black, plug in connector). The VSM350 has been activated by a local dealer and my viper online account is properly set up. I can update GPS information via the smartstart app (this confirms unit is powered up and communicating with the internet properly). I am not able to lock, unlock, or remote start using the app. When I attempt to lock/unlock or start, I receive the message "unlock failed at [time]" I have enabled H4 via flashlink. I live in a major city and the vehicle is parked outside, the issue is not related to cellular coverage; the app reflects that the vsm350 has 4 or 5 bars of signal strength. I appreciate any suggestions to enable the smartstart to communicate with the evo-all to enable the lock/unlock/remote start. Thank you
Login to reply View 1 answer(s)

05/02/2019

 Chevrolet Christina Cohoon (160Pts.)

0

Does engine have to cool down before I can remote start my car again?

My car (2013 Cruze) started last night and I drove it home. Once home I tried to start it again but it wouldn't. This morning it started fine and I drove to work. Once at work I tried to remote start it after 15 minutes of sitting but would not start. Is that normal? I didn't know if the engine had to cool down for it to remote start again. Thanks!
Login to reply View 1 answer(s)

05/02/2019

 Infiniti Nick Larsen (160Pts.)

0

2009 Infinity G37 OEM remote No Start

I just finished installing the EVO-NIST1 (no other components) on my 2009 Infinity G37. After hooking up the wiring harness I completed the bypass programming procedure and everything went good until I tried to start the car using my OEM remote. I pushed my OEM remote 3 times and the car did not start. Each time I pushed the lock button a blue LED light flashes on the EVO unit but nothing else happens. Do I need to order a stand alone remote? Do I need additional components? Not sure what to do here.
Login to reply View 1 answer(s)

03/02/2019

 Hyundai AZIZ ABOUD (140Pts.)

0

EVO-ALL hyundai sonata PTS 2011 i have to connect door lock to the module or not ?

HYNDAI SONATA PUSH TO START 2011
Login to reply View 1 answer(s)

30/01/2019

 Jeep Javier Solla Rivera (130Pts.)

0

Installing EVO CHRT5 Stand Alone on 2007 jeep compass and wont start; can't find +Starter wire on 5 pin Conector?

I am installing an EVO-CHRT5 Stand alone preloaded on my daughter's 2007 jeep compass limited, with installation guide (F) and can't find + starter wire on 5 pin conector under steering wheel. It suposed to be the 2nd pin out of 5 of the black conector. Installed everything else and completed program sequence. when close vehicle and pressed 3 times the lock, it flashes back, sound one horn of acknowledge; even hear the fuel pump priming, lights on dash light up but no start. Contacted seller and told me to follow instalation guide (F) from Fortin site. Have tried disconecting plugs and reprograming module sequence and does the same; NO START. Need help please. Thanks
Login to reply View 1 answer(s)

25/01/2019

 GMC Seth Harding (130Pts.)

0

Remote Start + RF Kit = What am I missing?!

Hello,
I have a 2003 GMC Yukon XL I am trying to install a remote start on. We have the Evo-One, RF kit RF641W, and Flash Link Updater. I cant get the remotes to program. Im not seeing any installation instructions except for the bypass module: Guide 61101. Ive performed installation. It wont start.
Is there an installation guide for the remotes?
What am I missing?

Any help would be appreciated.
Thanks

Login to reply View 1 answer(s)

25/01/2019

 Ram Radoslaw Patora (740Pts.)

0

RAM 2500 DIESEL KEY+EVO ALL - REMOTE NOT WAITING FOR A GLOW PLUG

RAM 2500 2014 6.7 DIESEL + EVO ALL STAND ALONE 3X LOCK REMOTE START WORKS FINE BUT AFTER IGNITION ON DOES NOT WAIT FOR GLOW PLUG C1,D1,D2 ,AND DIESEL MODE IS ON
Login to reply View 1 answer(s)

22/01/2019

 Hyundai gursharan Hayer (160Pts.)

0

Evo one won't crank hyundai elantra

I installed evo one in my 2017 elantra.Updated the module with flashlink updater. Activated C1,D6 and 38.2. It is programmed in the car but when press lock 3 times accesory comes on for 1 sec and then shuts off. Does not crank at all
Login to reply View 1 answer(s)

18/01/2019

 Toyota Bhavesh Kumar (160Pts.)

0

2014 rav4 hkey with toy-3 harness, programming seems to have worked but does not remote start

I've connected all the required wires using the toy-3 harness (I don't have TPMS so did not connect those two and I didn't connect the hood pin contact). I updated the unit using the flash link updater to the settings in the guide. I programmed the evo-one and got all the lights as per the guide, after the blue led was flashing rapidly i turned off the ignition and the evo-all stopped flashing. When i press the lock button the blue light flashes each time but the rav4 does not remote start.
Login to reply View 1 answer(s)

13/01/2019

 Acura Giuseppe Dionisi (130Pts.)

0

Blue light not flashing when pressing lock button, no 3x start. Programs successfully.

2010 Acura TL key start with t harness
Login to reply View 1 answer(s)

12/01/2019

 Jeep Rylee Stevens (230Pts.)

0

2005 jeep grand Cherokee wiring problem

I made the extra connections as per 28831 - F I have an evo all with hardware 6 and newest firmware. I also have the 642 remotes. Everything works except starting the vehicle. The evo bypasses the built in immobilizer and the LEDs flash like it's trying to start.
Login to reply View 1 answer(s)

12/01/2019

 Ford Josh Howard (140Pts.)

1

Evo-FORT4 won't program

I am trying to install an EVO-FORT4 with t-harness on a 2012 Ford F150. Programmed to firmware v71.47 After connecting t-harness and plugging in the OBD connector, I try to program the EVO. While holding the program button, im plugging in the power connector and releasing the program button when the red and blue lights illuminate. Then connecting all remaining connectors. Then I insert key 1 for 3 seconds, then key 2, then back to key 1. The red and blue lights stay illuminated and no other lights illuminate. / Any ideas on what is wrong?
Login to reply View 1 answer(s)

07/01/2019

 Ram Loren Malcom (160Pts.)

0

Wired correctly, works, but dash goes nuts.

I have a 2014 ram 1500 with a tip key. I have the chrt6 evo all. Everything is hooked up correctly. But after it’s started the check engine light now is on and a bunch of other light come on including the TPMS, traction control, saying my fuel gauge sensor is bad. Blinker light on the dash not working. Etc... The directions call for a diode but doesn’t show where to put it in the schematics. Is this my issue? PLEASE HELP!
Login to reply View 1 answer(s)

06/01/2019

 Nissan Eric Laing (390Pts.)

0

EVO-ALL NIST1 no start, press brake light on.

I've done SOOOOOOOOO much searching and nothing has helped. 2016 Juke PTS T-harness, everything connected properly (verified voltage and connected PTS wire (black/white A19)). Brake lights come on after my programmed lock-lock-lock, Fortin clicks a few times (relays inside) but car won't start then the red LED blinks 3 times and that's it. The entire time the amber dash 'press brake' icon is displayed. Thinking I have now wasted my money buying this starter that after about a month of trying to install still does not work.
Login to reply View 2 answer(s)

31/12/2018

 Toyota Bret McKinney (190Pts.)

0

2005 Toyota Tacoma evo one starts up then dies

I have a evo one installed on a 2005 Toyota Tacoma, all programming went as described in the install guide. Truck starts then dies after about 6 seconds. Flashes parking lights 4 times after shutdown. Manual says that is because of no tach signal. I have option 20 set to tactless engine monitoring. My yellow wire loop is cut for my automatic transmission and valet mode is off. I have tried different older firmware versions on bypass and remote start sides. I have tried other options with no success. I have also tried key in the ignition with ignition off and doors closed. I’m using guide 58481. I bought fortin RF kit and programmed remotes. All functions work as desired but truck does not continue to run for the period of desired run time. i have not tried reversing tx and rx wires. i have not tried ignition set to on with the key, then remote starting.
Login to reply View 1 answer(s)

28/12/2018

 Ford Kenny Smith2 (130Pts.)

0

5 amp ignition fuse blowes every time the car is shut off.

I have installed the EVO-FORT1 in a 2015 Ford Focus. Now after the car is shut off either with the remote or key the 5 amp ignition fuse will blow. I have secured all the unsed wire ends and tied everything up. The only things that needed to be connected was the T- harness and the two datalink wires. Is it possible to have a bad interface module or do I need to wire in a relay to the module? I dont have the servce number because the module is installed under the dash.
Login to reply View 1 answer(s)

14/12/2018

 Dodge Bill Blasingame (130Pts.)

0

Correct ignition wire, pin number on what plug letter located on BCM passenger kick panel?

2016 Dodge Charger SE
EVO-All Ver.6 Firmware 74.32 with CHART6 harness

I have verified connection back to the EVO with meter. Ignition wire is one I am uncertain of. On the BCM I have metered every wire from harness A to G, I get 12V on both "pink/white" from BCM connector E.
When using either of the pink/white wires the car will turn over but die, or start n run less than 2 seconds, or till the EVO clicks again killing engine.

Please help, I planned to have this ready for Christmas.
Thank you,
Bill

Login to reply View 1 answer(s)

04/12/2018

 Subaru Andrew Hartung (210Pts.)

0

Where can the rear defroster wire be connected at?

2010 Subaru Forester. I want to connect the rear defogger/defrost to the remote start. Where is the wire and how do I tap into it? Wirecolor said it was the harness was at the BIU, a blue wire, but wirecolor has been wrong before. I've tried testing this wire with a multimeter, but am getting odd results. If I can tap this wire at the harness, do I program for pulse or latch? Do I need a relay? The wire form the remote start is 200mA(-).
Login to reply View 1 answer(s)

03/12/2018

 Other mrmoe (100Pts.)

0

What to do with the smart start 2 yellow wire?

Does the yellow wire from the smartstart 2 need to be connected to the evo one module? If so, where? I am using it with a THAR ONE MAZ3 harness. Thanks
Login to reply View 1 answer(s)

01/12/2018

 FAQ c hansen (310Pts.)

0

Cold start mode with telematics

Is there a way of enabling cold start mode with a drone installed on an evo one?
Login to reply View 2 answer(s)

28/11/2018

 Remote Starters BRIAN THOMAS (260Pts.)

0

2015 Rav4 won't start with Car Link ASCL6 smart phone app EVO-ONE installed

Hello. I have a EVO-ONE remote start in my 2015 Rav4 with a newly installed Car Link ASCL6 Telemantics module for cell phone remote start. I have also have the long range remote. The key fob 3x and long range remote works perfectly with no issues, but the cell phone app will not start the car. It shows the battery voltage in GREEN, cell signal in GREEN, door lock/unlock status, and GPS. When I touch the start button it won't start...the button turns blue then red showing it didn't start. It eventually goes back to white. The doors won't lock or unlock either, but it shows the status when I'm close to the car. I locked the doors with the fob and the status on the cell phone app changed to lock accordingly. When I unlocked the car with the fob it showed the unlock on the app correctly. I followed the installation instructions correctly and if I didn't install it correctly I'd think it wouldn't show the battery voltage and other things I mentioned above. Protocol is set to FORTIN so I got that right. Can anyone help? Thanks! Brian
Login to reply View 1 answer(s)

27/11/2018

 Hyundai Anthony Wilkinson (7090Pts.)

0

2018 Elantra PTS Remote trunk pop not working.

Everything else works; parking lights, remote start, key take over, door locks. The factory remote won't pop trunk when in remote start mode.
Login to reply View 2 answer(s)

No results

picto contact

Looking of our top participants?

See users
picto contact

Couldn’t find what you were looking for?

Ask a question

TECHNICAL SUPPORT

Search through our most popular products and installation topics available in our Question & Answers section.

Learn more
Download our step-by-step troubleshooting guides app available for both iOS and Android or browse through our desktop version.

Learn more
Access the industry’s largest online wiring diagrams & photo database. A free token is provided in every EVO-SERIES box.

Learn more
You did not find the information that you were lookingfor? Ask us a question by filling out the technical support form request. A product specialist will answer you shortly.

Learn more
From state-of-the-art vehicle remote control and connectivity solutions to premium technical support, learn why you should choose Fortin products.

Learn more

This website uses cookies to ensure you get the best user experience. By continuing to browse our site, you are agreeing to our use of cookies. Learn More Continue